DIY Loudspeakers: HOME  INDEX  UPDATES  RESPONSE  WHAT'S NEW 

Ellipticor-21-3
Copyright 2026 © Troels Gravesen

   Go to on this page:

DRIVERS    CROSSOVER     CABINET    WORKSHOP PICS     MEASUREMENTS     SPEAKER-KIT     CROSSOVER LAYOUT


If you are a lover of brass, of female vocals, of cymbals, of violins, of flamenco, of... well, you may be in love with a lot of things having high pitched sounds, a good 2" dome can do wonder. It can do wonder in bridging the midrange driver and a good tweeter. I relives the midrange driver of the upper-mid (possible beaming) and it allows the point of crossover between the mid-dome and tweeter to be out of the trouble zone. You may find that cymbals are now clearer with enhanced transparency. I have an old test LP with a flamenco track cut as the last track on one side and I never really liked the sound of this track being muddled and messy and the audience applause similarly. "The noisy flamenco", as Segovia once put it, should never be cut at the end of an LP. Ideally at the beginning and ideally at 45 rpm. Anyway, I found out the record wasn't that bad - and my cartridge neither (Anna-D).

Following my test of the VOLT VM527 (modded) I decided to make a 3-way from ScanSpeak Ellipticor drivers and the VOLT mid-dome. Aimed at the discerned listener who might not have the the space - or the permit - for a larger floorstander. Customers who might not opt for thunderous deep bass and who - as said - may like demanding music with regard to high-frequency content. That's obviously not to say it wouldn't be enjoyable for any other kind of music. It certainly is and the 21WE midbass can play some decent bass despite its limited size.

This is not a cheap speaker, and I don't expect a lot of people to build it, but it's going to be one of my few keepers. I googled the drivers and found something in the area of 3600 EUR for the drivers alone. Jantzen Audio can do a little cheaper, bit still, not a cheap speaker.

Should you want the the deep grunt of the bass, add a bass module with a Faital 10RS430 bass driver. This has been tried and does well - as does the ScanSpeak 28W/4878T01. In this setup I added a 1st order high-pass filter to my EAR-861 and crossover the bass drivers similarly at 80 Hz, LR2, reverse phase. Read here.

 

Basics:
3-driver speaker.
Dimensions: 28 x 36.3/37.5 x 57 cm, WxDxH.
System sensitivity: 90 dB/2.8V/1 meter.
Impedance: 4 Ohms.
Power requirement: 30+ watts/channel.



Useful links (Please follow all links before e-mailing!):
http://www.troelsgravesen.dk/tips.htm
http://www.troelsgravesen.dk/tips.htm#CONSTRUCTION_OF_CROSSOVERS
http://www.troelsgravesen.dk/crossovers.htm
http://www.troelsgravesen.dk/LCR-RC.htm
http://www.troelsgravesen.dk/Inverted-Polarity.htm
http://www.troelsgravesen.dk/choices.htm
http://www.troelsgravesen.dk/Placement-of-ports.htm




DRIVERS
BACK TO INDEX

  
ScanSpeak D2404/552000


VOLT VM527 mid-dome.
Read about modification here. Felt discs following the kit.

 


ScanSpeak 21WE/4542T00

 Download specs here:

D2404/552000    VOLT VM527    21WE/4542T00


CROSSOVER
BACK TO INDEX

One thing we have to do with all mid-domes is linearising impedance to get rid of the resonance peak! This goes - to my experience - for all larger domes as we tend to use them down to close to Fs. Fortunately we here have a mid-bass than does very well up to more than 2 kHz, so a wide range of crossover points available. And the mid-dome goes so high we have extra freedom to pick a suitable point of crossover between mid and tweeter. Generally life is easy with mid-domes and we can avoid crossing over to the tweeter where it is hurts the most.


CABINET
BACK TO INDEX

Cabinets were made from 20 mm Baltic birch for sides, top and bottom. Rear panel from 25 mm HDF and front panel from 30 mm solid oak with strips of maple wood.

Now, you can build the cabinets like above and tilt them some 5 degrees - or like below, well suited for ~45 cm stands depending on your listening height.

Third option is building the above and place them on higher stands to suit your listening height.


Workshop pics
BACK TO INDEX


Cabinets shaping up and ready for bitumen pads.

 
Routing front panels for drivers.

 


For the mid-dome routing must be done from both sides to make a panel thickness of 18 mm, so make sure you have a straight center routing hole all the way through.

 


Tweeter and mid-dome routing done - testing mid-dome routing.

 

 
If 30 mm front panel is used, chamfer 21WE hole like seen on photo.

 


Testing drivers - and adding bitumen pads.

 


Cover internal panels with felt. Glue with vinyl glue, same as for bitumen pads.
Leave mid section rear panel clean where the MT section crossover is placed.
Leave un-damped bottom panel in front of terminals, this for the bass crossover.

The layout for the upper brace was changed from what's seen on the photo.
Follow the drawing to give space for the mid-dome magnet when inserting the unit.

 


Acoustilux damping seen from bottom (left) and top (right).
Place 1 pcs 30x45 cm on top and top-sides.
Place 2 pcs 21 x 50 cm in middle section. Fasten with staples at top. This makes two layers on top of MT crossover.
Place 1 pcs 30 x 45 cm at bottom and up sides. Fold one piece 30 x 45 and place at bottom.

 

I used exactly 0.76 sqm felt, 1 sqm supplied.
I used exactly 1.2 sqm acoustilux, 1.5 sqm supplied.
I used 0.86 sqm bitumen pads, order 4 pcs if you decide (optional).

 

 


MEASUREMENTS
BACK TO INDEX

A few comments on MEASUREMENTS before you start interpreting the readings below.
First of all, if we think measurements will tell us how a speaker sounds, we're wrong. The perception of sound is way too subjective to be reflected in any measurements we can perform. A loudspeaker system is meant to give us a satisfying idea of an acoustic event and for some people a pair of 5 USD ear-plugs are enough, others spend 200 kUSD on a truly full-range pair of speakers - and the latter may not be happier than the former.
Measurements may give us an idea of tonal balance of a system, i.e. too much or too little energy in certain areas, although dispersion characteristics play a vital role here. A two-way 7+1 and a three-way 7+4+1 may display similar horizontal dispersion, yet sound very different. Measurements may tell us about bass extension if far-field measurements are merged with near-field measurements. In addition to this, ports may contribute to bass extension. Most of we diy'ers do not have access to an anechoic room for full-range measurements from 20-20000 Hz.  
What cannot be seen is what kind of bass performance we get in a given room. Bass performance is highly dependent on in-room placement of your speaker and the same speaker can be boomy in one place and lean in another. Actual SPL level at 1 meter distance and 2.8V input is useful for en estimate of system sensitivity and combined with the impedance profile may give an idea of how powerful an amplifier is needed to drive the speaker to adequate levels.
What measurements do not tell is the very sound of the speaker unless displaying serious linear distortion. The level of transparency, the ability to resolve micro-details, the "speed" of the bass, etc., cannot be derived from these data. Distortion measurements rarely tell much unless seriously bad, and most modern drivers display low distortion within their specified operating range. 
Many people put way too much into these graphs and my comments here are only meant as warning against over-interpretation. There are more to good sound than what can be extracted from a few graphs. Every graph needs interpretation in terms of what it means sonically and how it impacts our choice of mating drivers, cabinet and crossover design.
What measurements certainly do not tell is the sonic signature of the speaker, because speaker cones made from polypropylene, aluminum, Kevlar, paper, glass fiber, carbon fiber, magnesium, ceramics or even diamonds all have their way of adding spices to the stew. Nor do measurements tell what impact the quality of the crossover components add to the sound, from state of the art components to the cheapest of coils and caps, they all measure the same if values are correct, yet sound very different.

 


The most important part, the mid-dome.
This is easy!


Response of all driver on actual baffle without any crossover attached.
21WE merged with nearfield response at 250 Hz, port not included.
A healthy 90 dB sensitivity is assured.


Final response of speaker system.

 


SPEAKER-KIT
BACK TO INDEX

To configure a DIY kit and get a written offer including shipping cost, please use the DIY kit configurator in the Jantzen Audio website:



https://jantzen-audio.com/diy-kits/
 
Remember to add terminals when ordering at Jantzen website. No longer included in kit.

All technical questions to troels.gravesen@hotmail.com


CROSSOVER-LAYOUT
BACK TO INDEX

Check this out before start making crossovers:

http://www.troelsgravesen.dk/tips.htm#CONSTRUCTION_OF_CROSSOVERS

Also please read this:
http://www.troelsgravesen.dk/LCR-RC.htm


Layout for bass.

 


Layout for domes.


Took the picture too fast. Some corrections added to picture. Follow layout drawing.

 

Speaker wiring